牌号简介 About |
---|
为了满足UL94V-0的严格非燃烧要求,已经制定了50-3150 FR。50-3150 Fr黑色环氧树脂,催化剂190和催化剂30在保险商实验室列出,以通过UL94V-0。该系统具有优良的传热性能、低收缩率和优异的绝缘性能。50-3150Fr(催化剂30)的相对温度指数(RTI)为130°C。50-3150Fr(催化剂190)的黑色催化剂根据ASTM E595-07通过了NASA的排气要求。50-3150 fr的典型应用包括封装电源、变压器、线圈、绝缘体、传感器等。该系统是需要高导热性和阻燃性的应用的最佳选择。 50-3150 FR has been formulated to meet the stringent non-burning requirements of UL94 V-0. 50-3150 FR Black Epoxy with Catalyst 190 and Catalyst 30 are listed with Underwriter's Laboratory for passing UL94 V-0. This system offers excellent heat transfer, low shrinkage, and outstanding insulation properties. 50-3150FR with Catalyst 30 has a UL (746B) Relative Temperature Index (RTI) rating of 130°C. 50-3150FR Black with Catalyst 190 passes NASA's outgassing requirements per ASTM E595-07. Typical applications for 50-3150 FR include encapsulating power supplies, transformers, coils, insulators, sensors, etc... This system is an excellent choice for applications requiring high thermal conductivity and flame retardancy. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
收缩率 Shrinkage rate |
|||
MD MD |
0.20 | % | |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
线性热膨胀系数 Linear coefficient of thermal expansion |
|||
MD MD |
1.4E-5 | 1/℃ | |
导热系数 Thermal conductivity coefficient |
2.2 | W/m/K | |
热变形温度 Hot deformation temperature |
155 | ℃ | |
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
工作温度 working temperature |
-60.0 到 200 | ℃ | |
Outgassing Outgassing |
|||
Uncured Properties Uncured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
颜色 colour |
|||
密度 Density |
|||
25℃ 25℃ |
g/cm³ | ||
粘度 viscosity 3 |
|||
25℃ 25℃ 3 |
Pa·s | ||
Cured Properties Cured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 D Shaw's D |
|||
拉伸强度 tensile strength |
MPa | ||
压缩强度 compressive strength |
MPa | ||
耐电强度 Electrical strength |
kV/mm | ||
相对电容率 Relative permittivity |
|||
60 Hz 60 Hz |
|||
体积电阻率 Volume resistivity |
|||
25 ℃ 25 ℃ |
ohms·cm | ||
耗散因数 Dissipation factor |
|||
60 Hz 60 Hz |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 Part A |
【新闻资讯】查看全部
塑料顶级工业设计玩出新高度!
2017-08-31 材料是工业设计中非常重要的环节,对材料的认识和掌握是实现产品设计的前提和保证。 包豪斯学校的灵魂教师伊顿曾经说道:“当学生们陆续发现可以利用各种材料时,他们就能创造出更具有独特材质感的作品。 ” 我们要了解材料,尊重材料,最大限度地利用材料。这是一个工业设计者必须具备的一个基本素质。 让我们一起来看看设计师们对塑料材料是如何玩出新高度的~ |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |